Is The Eac Electric Air Cleaner Better Than A Cartridge Filter

Honeywell Collector Cell F50A F50E F50F F300 F52 12½ x 20

Part Number: FC37A1064

Description

10 10 sixteen

12½ 10 16

10 x twenty

12½ x xx

12½ 10 20

FC37A1171
FC37A1064
FC37A1049
FC37A1130
FC37A1114

FC37A1064 xx ten 12½ x 4½". Genuine Honeywell electronic air cleaner jail cell. Notation, Honeywell 20 10 25" air cleaners use two cells. Assembled with ionizing wires and set to slide in and utilize.

Honeywell cells are symmetrical so they can be used with air flow going right or left. The cell is simply flipped around for the opposite air flow.

Includes one plastic handle 137266. The handle can mount on either end of the cell allowing the jail cell to be rotated and used with air flow running in either direction. Make up one's mind the side of the cell that will exist facing out before installing the handle.

Since 1975 all F50A F50E F50F F300 apply cells listed in the first 4 tabs above. The FC37A1171 is only used in the F52 grille mount. The current production cells are the same as the early on cells that had the red fiberglass contact pad.

The Honeywell FC37A1064 cell tin be identified by the function number stamped in to the aluminum. The textHoneywell Residential is stamped in the end facing out and the part number is stamped in to a side border, see photo beneath.

The FC37A1064 is used in F300E1035 F300A2025 F50F1065.
Used in F300A2012 F300F2012 F50F1040 F50F1057.
All F50A F50E units size 20x25 and 20x12½.
Honeywell Collector Cell part number location

Collector Cell Washing

collector cell dirt on plates We recommend soaking the collector cells. Soaking cleans better than the dishwasher and cleans better than a pressure washer. The cells typically do not need to be cleaned as often every bit the prefilters.

After cleaning, inspect the prison cell plates for dirt, hold the jail cell up to light. View the plates through the ionizing section to see the dirtiest side. Note that only every other plate captures clay.

The plates are either charged or grounded. The charged particles are attracted to the grounded plates and repelled by the charged plates. Closely bank check the grounded plates, where as the charged plates will make clean easily.

Honeywell Instructions
White-Rodgers Instructions
Cell Washing Frequency

Cleaning Ionizing Wires

Deposits of solid silicon dioxide Honeywell recommends wiping down the ionizing wires when washing the collector cells. Also check the wires for roughness, a side effect of the corona discharge is the growth of a white quartz layer.

Air near the high-voltage ionizer wires breaks downwardly in to ions and high free energy electrons. This mixture of ions and electrons is called the corona plasma. The ions collide with suspended particulate and confer the charge.

The plasma has an unintended reaction with cyclomethicone, a silicone oil present in household products such every bit deodorant sprays and skin lotions. This reaction leaves deposits of solid silicon dioxide on the ionizing wires. These insulating formations will significantly suppress the corona pattern and intensity.

Inquiry has shown cleaning the wires with 600 grit emery cloth will remove the silicon dioxide. But at the risk of dissentious the wire surface or breaking the wire.

Existent-Life Exposure

Prison cell Handle Installation

The handle swings in to place and snaps in. Be sure to as well snap downward the locking tab. Click photo for detailed teaching.

Cell handle installation

Fixing Cell Arcing

determining cell sparking area If a cell is sparking, determine the sparking area and removed cell to audit closer. To see the sparking, you may need to look in through the blower compartment or cut an inspection hole in the duct. An inspection window can also be used to see if cells need to be cleaned.

A cell that is sparking randomly throughout is uncommon but could be acquired by a film left behind from washing. If tobacco is not cleaned from a cell it can build upwards and crusade random sparking. Diesel fumes can cause problems and are not easily cleaned. Loftier altitude can brand the air cleaner more susceptible to sparking. The collector plates should be cleaned to the bare shiny metallic (stained is okay).

Major prison cell sparking can be the result of power box wires getting crossed. The prison cell is powered by two voltages. The ionizing wires receive 8kv and the plates get 4kv. If these voltages get crossed, then the cell will spark all over and much louder than normal.

If a jail cell is shorted and keeps the neon lamp from coming on, then inspect for damage. The nigh common brusque is from the aluminum dividers in between the ionizing wires. These dividers tin get pushed in to the collector plates, they should not impact the plates. A dent across several plates causing them to bear upon would be a simple short to detect. A dandling ionizing wire can cause a short. determining cell sparking area

Continuous Cell Arcing

continuous arcing by tabs contact with edge of every other plates The 4074EHG tabs brand contact with the edge of every other prison cell plate. Photograph right shows the edges of the plates burnt down far enough, that the contact shorts confronting every plate and not every other.

Honeywell cells tin can concluding for decades, but continuous sparking tin can cause damage. A cell may spark continuous if collector plate spacing gets also close. The spacing can become uneven when a cell gets pushed out of square, twisted, a dent, etc.

I common problem is a loose plate that has lost the press fit with its horizontal rods. The loose plate likely had continuous sparking that created surges of current through the press fit. The current surges resulted in sparks that burden away the press fit. This prison cell would non exist repairable.

When one prison cell has been subject to excessive sparking, then both cells will exist burnt under the contact pad. This is because a spark in one cell will cause a current surge that is drawn from both cells.

Check the contact pad to determine the status of the cell. If your cells accept badly burnt contacts as in the photo above, and then it is all-time to supersede the cells.

When a cell has been subjected to excessive sparking, the press fit of all the plates will starting time be weakened. The sparking at these connections causes corrosion from ozone. The aluminum around the press fit becomes corroded and no longer conducts likewise.

The cell contacts operate at high voltage and are not a sensitive connection. The contact does not require cleaning. The contact is can coated copper. Sandpaper will remove the tin coating.

The photo below shows arcing under the contact pad.

Cell Contains 3 Contacts but Only 2 Used

You lot may have noticed there are 3 contacts on the prison cell pad only only two contacts at the power box. This allows the F50-F300 to be installed with either right or left air flow. The cell can be rotated assuasive an installation with opposite air catamenia.

Just two contacts are used, the centre contact and ane terminate contact. Photograph animation shows when the cell is rotated, the contacts maintain the correct connections.

The centre contact powers the ionizing wires. The ii outside contacts are continued and power the collector plates.